101-1063-009 New Hydraulic Motor Compatible for Eaton Char-Lynn H Series High Torque Low Speed Gerotor Hydraulic Motor for Construction & Agriculture
101-1063-009 건설 및 농업용 이튼 차린 H 시리즈 고속 제로터 유압 모터와 호환되는 새로운 유압 모터
| 상품번호 | B0GHYCNYQW |
| 상태 | New |
| 브랜드 | SINOCMP |
| 판매자 | SINOCMP Excavator Parts |
| 출고국 | 미국 (US) |
아마존 판매가
$159.99
약 235,825원
구매대행 예상 비용은 로그인 후 확인하실 수 있습니다.
상품 특징
[🔧] Direct Swap – 17.9 cu/in Displacement: This hydraulic motor 101-1063-009 replaces Char-Lynn Eaton H Series models with 17.9 cu in/rev (294 cc/rev) displacement. The 4-bolt square flange mount with 1.75 inch pilot diameter lets this 101-1063-009 hydraulic motor bolt directly onto forage harvesters, conveyors, and industrial sweepers without modifications.
[⚙️] High Torque – 3110 lb-in at 192 RPM: This H series hydraulic motor delivers 3110 lb-in (351 Nm) continuous torque at just 192 RPM, with max continuous pressure 1350 PSI and intermittent pressure up to 1800 PSI. The three-moving-part gerotor design with optimized drive running angle helps this 101-1063-009 replacement hydraulic motor maintain consistent power for demanding low-speed high-torque applications.
[🛢️] SAE O-Ring Ports – 7/8-14 UNF: For Char-Lynn hydraulic motor features 7/8-14 UNF-2B SAE O-ring side ports (aligned configuration) for reliable leak-free sealing. The O-ring design on this 101-1063-009 hydraulic motor creates connections without thread sealant, saving installation time on agricultural and industrial equipment. No case drain required.
[🏗️] Splined Shaft – SAE 6B with 1 Inch Diameter: This 101-1063-009 replacement hydraulic motor comes with SAE 6B splined shaft (1 inch diameter, 1/4-20 UNC-2B threaded end hole) for secure torque transmission without key wear issues. Cast iron housing with primer low gloss black finish. Hydrodynamic journal bearings on both front and rear for extended service life. Maximum flow 15 GPM.
[📦] Ready-to-Install – Complete Assembly: Box contains one hydraulic motor 101-1063-009 with splined shaft. Important: Verify 1.75 inch pilot diameter and 4-bolt pattern (3/8-16 UNC-2B) before ordering. Flush hydraulic lines prior to installation. Max operating temp 180°F. Recommended filtration ISO 4406 18/13. Replacement seal kit 60540-000 (Buna-N).
[⚙️] High Torque – 3110 lb-in at 192 RPM: This H series hydraulic motor delivers 3110 lb-in (351 Nm) continuous torque at just 192 RPM, with max continuous pressure 1350 PSI and intermittent pressure up to 1800 PSI. The three-moving-part gerotor design with optimized drive running angle helps this 101-1063-009 replacement hydraulic motor maintain consistent power for demanding low-speed high-torque applications.
[🛢️] SAE O-Ring Ports – 7/8-14 UNF: For Char-Lynn hydraulic motor features 7/8-14 UNF-2B SAE O-ring side ports (aligned configuration) for reliable leak-free sealing. The O-ring design on this 101-1063-009 hydraulic motor creates connections without thread sealant, saving installation time on agricultural and industrial equipment. No case drain required.
[🏗️] Splined Shaft – SAE 6B with 1 Inch Diameter: This 101-1063-009 replacement hydraulic motor comes with SAE 6B splined shaft (1 inch diameter, 1/4-20 UNC-2B threaded end hole) for secure torque transmission without key wear issues. Cast iron housing with primer low gloss black finish. Hydrodynamic journal bearings on both front and rear for extended service life. Maximum flow 15 GPM.
[📦] Ready-to-Install – Complete Assembly: Box contains one hydraulic motor 101-1063-009 with splined shaft. Important: Verify 1.75 inch pilot diameter and 4-bolt pattern (3/8-16 UNC-2B) before ordering. Flush hydraulic lines prior to installation. Max operating temp 180°F. Recommended filtration ISO 4406 18/13. Replacement seal kit 60540-000 (Buna-N).
상품 설명
Complete SpecificationsDisplacement: 17.9 cu in/rev (294 cc/rev)Max Continuous Torque: 3110 lb-in (351 Nm)Max Continuous Speed: 192 RPMMax Continuous Pressure: 1350 PSI (93 bar)Max Intermittent Pressure: 1800 PSI (124 bar)Max Continuous Flow: 15 GPM (57 L/min)Pilot Diameter: 1.75 inch (44.45 mm)Bolt Circle: 3.25 inch (82.55 mm)Mounting Bolts: 3/8-16 UNC-2BShaft: SAE 6B Splined, 1 inch diameterPorts: 7/8-14 UNF-2B SAE O-ring (side, aligned)Housing: Cast iron, primer low gloss blackMax Operating Temp: 180°F (82°C)Weight: 13 lbs (5.9 kg)What You ReceiveYour order includes one hydraulic motor (101-1063-009 specification) with SAE 6B splined shaft. Mounting bolts and port caps are not included. Inspect the motor upon arrival.Installation Notes⚠️ Verify pilot diameter (1.75 inch), bolt pattern (4-bolt on 3.25 inch circle), and shaft type (SAE 6B splined) before ordering.⚠️ Flush hydraulic lines prior to installation to remove contaminants.⚠️ Recommended filtration: ISO 4406 cleanliness code 18/13.⚠️ Recommended viscosity: 100-200 SUS (20-43 cSt) at operating temperature.⚠️ Replacement seal kit: 60540-000 (Buna-N) or 60544-000 (Viton).